QIACHIP Wireless 433Mhz RF Module Receiver and Transmitter Remote Control Built-in Learning Code 1527 Decoding 4 Channel Output Transmitter and Receiver kit

Shenzhen Keshilian Electronic Technology Co., Ltd EXPSFD006756 - Receiver module product model: RX480-E4 Working Voltage : DC3. 3~5v quiescent current : ≤5ma output current : 10 ma working frequency: 433mhz receive sensitivity: -108db working Temperature : -25~75 Working mode: Momentary Mode, self-locking Toggle-Mode of the 4 Channels, interlocking The output: 4 channel CMOS level signal Corresponding to the remote control ABCD 4 buttons.

Response: LED flashes 7 times. Led indicator flashes three times: learning successfully completed. Press any button of the remote control. Test: after the above operation, the receiver board can be controlled by the remote control. Transmitter module product model: tx118sa-4 transmitting power: 11dbm emission current: 10 ma rate of fire: maximum 10KB / S Operating Voltage: DC 3V-24V Encoding : EV1527 1527 Learning code Each module has a unique ID address code.

QIACHIP Wireless 433Mhz RF Module Receiver and Transmitter Remote Control Built-in Learning Code 1527 Decoding 4 Channel Output Transmitter and Receiver kit - Small size. 3. 2. Multiple working modes : Momentary Mode, Toggle Mode, interlocked mode. Learning remote code: press learning buttonon the receiver once, twice or three times see below. Pins instruction gnd : ground or negative pole +V : DC3.

More information about Shenzhen Keshilian Electronic Technology Co., Ltd EXPSFD006756

UCEC XY-MK-5V / XY-FST 433Mhz Rf Transmitter and Receiver Module Link Kit for Arduino/Arm/McU/Raspberry pi/Wireless DIY6-pack

UCEC 10 - Working voltage: 3v-12V Working current: 20-28mA. Working temperatur: -10 degree to +70 degree resonance mode: sound wave resonance SAW Modulation mode: ASK /OOK Working frequency: 315MHz-433. 92mhz, customized frequency is available. Transmission power: 25mw 315mhz at 12v frequency error: +150khz max Velocity: ¡Ü10Kbps Self-owned codes: negative RX Technical Specifications: Working voltage: 5.

0vdc static current:4ma working temperatur: -10 degree to +70 degree Working principle: single chip superregeneration receiving Working method: OOK/ASK Working frequency: 315MHz-433. 92mhz, customized frequency is available266-433MHZ. Transmission distance:>500m, sensitivity to -103dBm, in open areas.

UCEC XY-MK-5V / XY-FST 433Mhz Rf Transmitter and Receiver Module Link Kit for Arduino/Arm/McU/Raspberry pi/Wireless DIY6-pack - Bandwidth: 2mhz 315mhz, having result from testing at lowing the sensitivity 3dBm Sensitivity: excel ¨C100dBm 50¦¸ Transmitting velocity:.

More information about UCEC 10


Similar products



DAOKI 10pcs 433MHz antenna Helical Spiral Spring Remote Control for Arduino Raspberry 5mm

DAOKI BG-US-932781 - Input impedance OHM: 50 Max-power dBm: 30 . Features: frequency range mhz: 433MHz+ / -6MHz Gain dBi: 2. 2 input impedance ohm: 50 max-power dbm: 30 diameter: 5 mm length mm: 34+/-1 including welding part length Height mm: 20+/-1 Exposed parts, does not contain the welding part length Connector type: Direct weldment Package included: 10 x 433MHz helical antenna Tx working voltage: 3v-12v.

Rx working voltage: 5. 0vdc. Diameter: 5 mm. Gain dbi: 2. 2. Modulation mode: ASK /OOK. Static current:4MA. Frequency range mhz: 433MHz+ / -6MHz. Working principle: single chip superregeneration receiving. Working current: 20-28mA. Resonance mode: sound wave resonance SAW.

More information about DAOKI BG-US-932781


Similar products



HiLetgo 315Mhz RF Transmitter and Receiver Module link kit for Arduino/ARM/MCU/Raspberry pi

HiLetgo® 3-01-0082 - Frequency range mhz: 433MHz+ / -6MHz. Static current:4MA. Modulation mode: ASK /OOK. Max-power dBm: 30 . Tx working voltage: 3v-12v. Working current: 20-28mA. Resonance mode: sound wave resonance SAW. Diameter: 5 mm. Input impedance OHM: 50 Working principle: single chip superregeneration receiving. Gain dbi: 2. 2. Rx working voltage: 5.

More information about HiLetgo® 3-01-0082


Similar products



HiLetgo 5 Sets 433M Transmitter + Receiver Kit High Frequency Super Regenerative Transceiver Module for Burglar Alarm

HiLetgo - Static current:4MA. Wireless transmitter modules allow your Arduino to wirelessly comunicate with other arduinos, or with radio frequency RF controlled devices that operate in the same frequency 433Mhz in this case. Frequency range mhz: 433MHz+ / -6MHz. Input impedance OHM: 50 When using, the receiving frequency, decoding method and oscillation resistance should match with the transmitting.

Gain dbi: 2. 2. This radio transmitter & receiver pair is perfectly matched to allow you to control items from a distance up to 500 feet wirelessly! Working principle: single chip superregeneration receiving. When installing, far away from the shielding body, the antenna should be as straight as possible, high voltage and interference source.

HiLetgo 5 Sets 433M Transmitter + Receiver Kit High Frequency Super Regenerative Transceiver Module for Burglar Alarm - Working current: 20-28mA. Resonance mode: sound wave resonance SAW. If you want to automate your house without pulling cables then this device will help you well. Rx working voltage: 5. 0vdc. Max-power dBm: 30 Modulation mode: ASK /OOK.

More information about HiLetgo


Similar products



WHDTS 5PCS RCWL-0516 Microwave Radar Sensor Smart Switch Module Human Body Induction Module 5-7M Detection Distance 4-28V 100mA

WHDTS 855655 - If you want to automate your house without pulling cables then this device will help you well. Static current:4MA. Input impedance OHM: 50 Modulation mode: ASK /OOK. Diameter: 5 mm. Equipped with the special signal processing chip RCWL-9196. Gain dbi: 2. 2. Rx working voltage: 5. 0vdc. Easy to use, nice range using antenna on both, you can send strings text from one point to another.

Working principle: single chip superregeneration receiving. Max-power dBm: 30 Product Introduction: 1. Operating voltage:4-28V 2. Operating Current:2. 8ma typical;3mA max 3. Detection Distance:5-7m 4. Transmitting power:20mW typical;30mW max 5. Output Voltage:3. 2-3. 4v 6. Output voltage Driving Capacity:100mA 7. Trigger Way:repeat trigger 8.

More information about WHDTS 855655


Similar products



DAOKI 5PCS 315Mhz RF Transmitter and Receiver Link kit for Arduino/ARM/MCU/Raspberry pi Wireless

DAOKI TS-US-076_5 - Max-power dBm: 30 Working principle: single chip superregeneration receiving. Description:tX Technical Specifications:Receiver module parameters1. Product model: MX-05V2. Operating voltage: DC5V3. Quiescent Current: 4mA4. Receiving frequency: 315MHZ5. Receiver sensitivity:-105DB6. Size: 30 * 14 * 7mm7. External antenna: 32cm single core wire, wound into a spiralTechnical parameters of the transmitter head1.

Product model: MX-FS-03V2. Launch distance :20-200 meters different voltage, different results3. Operating voltage :3. 5-12v4. Dimensions: 19 * 19mm5. Operating mode: AM6. Transfer rate: 4KB / S7. Transmitting power: 10mW8. Transmitting frequency: 315M9. An external antenna: 25cm ordinary multi-core or single-core line10

DAOKI 5PCS 315Mhz RF Transmitter and Receiver Link kit for Arduino/ARM/MCU/Raspberry pi Wireless - Pinout from left ? right: data; vcc; gnd application environmentremote control switch, remote control door opener, electric doors, door closing device control system, remote control motorcycle remote control electric cars, remote volume gate, alarm host, receiver module, remote control socket, garage door remote control, remote control curtains, automobile anti-theft products, remote control retractable doors, pan doors, alarm, remote audio remote control electric doors, windows, home security products, motorcycles, remote control LED, shutter doors, remote control MP3.

More information about DAOKI TS-US-076_5


Similar products



ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 Nano x 3 Without Cable

ELEGOO EL-CB-005 - Easy to use, nice range using antenna on both, you can send strings text from one point to another. Wireless transmitter modules allow your Arduino to wirelessly comunicate with other arduinos, or with radio frequency RF controlled devices that operate in the same frequency 433Mhz in this case. Modulation mode: ASK /OOK.

Working principle: single chip superregeneration receiving. Compatible with sparkFun's 434MHz RF transmitter and RF receiver. Use the driver from above link. It is a smallest, complete, and breadboard friendly board. Static current:4MA. The nano is using the chips atmega328p and cH340, not FT232 as official Arduino, so pls.

ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 Nano x 3 Without Cable - It has more or less the same functionality of the Arduino/Genuino UNO, but in a different package. Rcwl-0516 is equipped with Doppler radar technology which is specially for detecting the motion of objects. Rx working voltage: 5. 0vdc. Widely used for human body adaptive forward lighting system, security alarm system and so on.

It has everything that diecimila/Duemilanove has electrically with more analog input pins and onboard +5V AREF jumper. Nano's got the breadboard-ability of the boarduino and the mini+usb with smaller footprint than either, RX, GND on one top, ATN, so users have more breadboard space.

More information about ELEGOO EL-CB-005


Similar products



INSMA 433Mhz Wireless RF Switch Long Range DC 12V 4CH Channel Wireless Remote Control Switch, DC12V Relay Receiver Module, Transmitter Toggle Switch RF Relay 2 Transmitter & 1 Receiver

INSMA CECOMINOD029486 - Jog: the cutting-out cap is non-occupation, JP1 and JP2 do not connect either. Equipped with the special signal processing chip RCWL-9196. Feature with high sensitivity, board detection angle, detection distance of 5-7M, widely power supply range of 4.0-28. 0v and so on. Compared with the traditional infrared induction PIR, it's has the penetration detection ability.

They work in pairs, meaning you need both a receiver and a transmitter to comunicate with each other. Jog: press one button is on, loosen your finger on the same button is OFF need one channel switch and one buttons remote control. Remote distance: 328ft/100M 2. Working temperature: -40 Degree +80 Degree 4.

INSMA 433Mhz Wireless RF Switch Long Range DC 12V 4CH Channel Wireless Remote Control Switch, DC12V Relay Receiver Module, Transmitter Toggle Switch RF Relay 2 Transmitter & 1 Receiver - Widely used for human body adaptive forward lighting system, security alarm system and so on. Working current: 20-28mA. Resonance mode: sound wave resonance SAW. 2. Press the learning code, press any button of the remote control, the indicator flash, loosen finger, the indicator flash 2 times and off, it means learning successfully.

Stable and reliable performance, high receive sensitivity. Wide application】wide range of applications from simple domestic remote control to autonomous control such as, alarm system, entrance, we are always here to help, window, lifting equipment and so on.

More information about INSMA CECOMINOD029486


Similar products



Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino

Elegoo EL-CP-004 - Working principle: single chip superregeneration receiving. Working current: 20-28mA. Resonance mode: sound wave resonance SAW. Working current: 20-28mA. Resonance mode: sound wave resonance SAW. Working principle: single chip superregeneration receiving. Diameter: 5 mm. So we can control the quality of our productions by ourselves for you.

Tx working voltage: 3v-12v. The power source is automatically selected to the highest voltage source. Long range】 signal can pass through walls, floors and doors, steadily control receiver from any place within a reliable distance. Easy to use, nice range using antenna on both, you can send strings text from one point to another.

Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino - Max range is up to 98ft/30m with no obstacle. 4ch for more control】adjustable working way, control equipment turn/reverse, on/off. Switch self-lock, Jog, Inter-lock. Security control】learning code has high-level security for its low repetitive rate and re-learn mode, by which it can delete the old code and re-learn a new code when a remote control get lost, so you are always in control of it.

Easy to use】extremely easy to setup, learn, relearn and controlplease refer to introduction. Widely used for human body adaptive forward lighting system, security alarm system and so on. You could download the driver of Elegoo Nano V3.

More information about Elegoo EL-CP-004


Similar products



SMAKN® 433Mhz Rf Transmitter and Receiver Link Kit for Arduino/Arm/McU

SMAKN 6461060 - Working temperatur: -10 degree to +70 degree resonance mode: sound wave resonance SAW Modulation mode: ASK /OOK Working frequency: 315MHz-433. 92mhz, customized frequency is available. Working voltage: 3v-12v Working current: 20-28mA. Transmission power: 25mw 315mhz at 12v frequency error: +150khz max Velocity: ¡Ü10Kbps Self-owned codes: negative RX Technical Specifications: Working voltage: 5.

0vdc static current:4ma working temperatur: -10 degree to +70 degree Working principle: single chip superregeneration receiving Working method: OOK/ASK Working frequency: 315MHz-433. 92mhz, customized frequency is available266-433MHZ. Bandwidth: 2mhz 315mhz, having result from testing at lowing the sensitivity 3dBm Sensitivity: excel ¨C100dBm 50¦¸ Transmitting velocity:.

SMAKN® 433Mhz Rf Transmitter and Receiver Link Kit for Arduino/Arm/McU - Transmission distance:>500m, sensitivity to -103dBm, in open areas.

More information about SMAKN 6461060


Similar products