As an Amazon Associate I earn from qualifying purchases.



Easy to use no assembly required. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.


Just wire up motors and power, easy to use. This l298n board comes ready to go. Double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.



Protection features: overcurrent protection ocp, Thermal Shutdown TSD, vM Undervoltage Lockout UVLO; Integrates 5V regulator, allows providing power to Raspberry Pi.

1. SMAKN
#ad
SMAKN CNC Micro-Stepping Stepper Motor Driver M542/DM542 Bi-Polar 2phase 4.5A Switch
#adSMAKN #ad - Up to 32 segments of six kinds of sub-modes available. H-bridge bipolar constant phase flow driver. The maximum output current is 4. 5a eight optional. The input signal high-speed photoelectric isolatio. 24v-50v dc power supply.More information #ad
Brand | SMAKN #ad |
Manufacturer | SMAKN #ad |
More information #ad
2. DAOKI
#ad
DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
#adDAOKI #ad - Package included - 5 pcs L298N Motor Driver Controller Board Modules. Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously.More information #ad
Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. The signal is shown in the figure. The connecting method is shown inbelow figure after enable ENA ENB.Brand | DAOKI #ad |
Manufacturer | DAOKI #ad |
Part Number | FBA_TS-US-078-SNL |
Model | FBA_TS-US-078-SNL |
More information #ad
3. Adafruit
#ad
Adafruit TB6612 1.2A DC/Stepper Motor Driver Breakout Board
#adAdafruit #ad - 7mm x 19mm x 3mm / 1. 1" x 07" x 01". Current limit: 1. 2a, 3a peak max. Soldering of header pins required.More information #ad
Brand | Adafruit #ad |
Manufacturer | Adafruit Industries #ad |
Height | 1 Inches |
Length | 2 Inches |
Width | 1 Inches |
Part Number | ADA2448 |
Model | COMINU039720 |
More information #ad
4. TIMESETL
#ad
TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects
#adTIMESETL #ad - This l298n board comes ready to go. High efficient double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient.Easy to use no assembly required. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
More information #ad
High quality main driver chip l298n, strong anti-interference, low calorific value, afterflow diode protection, strong driving ability, more stable and reliable for Arduino projects. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Just wire up motors and power, easy to use.Brand | TIMESETL #ad |
Manufacturer | TIMESETL #ad |
Height | 1.18 Inches |
Length | 5.91 Inches |
Width | 3.15 Inches |
Part Number | TXJ-061-EU |
Model | L298N motor controller |
More information #ad
5. HiLetgo
#ad
HiLetgo 2pcs A3967 Stepper Motor Drive Board EasyDriver Stepper Motor Driver for Arduino Raspberry Pi Robot
#adHiLetgo #ad - The easydriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse or 0 to 3. 3v pulse if you solder SJ2 closed on the EasyDriver. I. E. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control.More information #ad
Easydriver drives bi-polar motors, and motors wired as bi-polar. The easydriver has an on board voltage regulator for the digital interface that can be set to 5V or 3. 3v. Easydriver requires a 7v to 30V supply to power the motor and can power any voltage of stepper motor. 4, 6, or 8 wire stepper motors.Brand | HiLetgo #ad |
Manufacturer | HiLetgo #ad |
Part Number | 3-01-0831 |
Model | 3-01-0831 |
More information #ad
6. MELIFE
#ad
MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
#adMELIFE #ad - Main driver chip l298n, strong driving ability, low calorific value, afterflow diode protection, strong anti-interference, more stable and reliable for Arduino projects.Just wire up motors and power, easy to use. This l298n board comes ready to go. Double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
More information #ad
No assembly required. Great for arduino diy smart car robot power uno mega r3 mega2560 duemilanove. External size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.Brand | MELIFE #ad |
Manufacturer | MELIFE #ad |
Part Number | 15489 |
More information #ad
7. STEPPERONLINE
#ad
STEPPERONLINE Short Body Nema 17 Bipolar Stepper Motor 1A 22.6oz.in/16Ncm DIY CNC Extruder
#adSTEPPERONLINE #ad - Nema 17 bipolar 1. 65"x1. 65"x079" 4-wire. Short height, Small Size. 1. 8 deg. 16ncm22. 6oz. In holding torque. Rated current 1. 0a & resistance 3. 5ohms. Step angle200 steps/rev.More information #ad
Brand | STEPPERONLINE #ad |
Manufacturer | OSM Technology Co.,Ltd. #ad |
Height | 0.79 Inches |
Length | 1.65 Inches |
Weight | 0.31 Pounds |
Width | 1.65 Inches |
Part Number | 17HS08-1004S |
Model | 17HS08-1004S |
More information #ad
8. Longruner
#ad
Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire
#adLongruner #ad - Cable length: about 20cm /8-inch. A, c, b, d four-phase led indicates the status of the stepper motor work. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board. Stepping angle: 5. 625 x 1/64.More information #ad
Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs. Good after-sales service. 5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. Motor diameter: 1. 1 inches. Wire length:9. 05 inchs. Stepper motor with a standard interface.Brand | Longruner #ad |
Manufacturer | Longruner #ad |
Part Number | LK67 |
Model | LK67 |
Warranty | 1 year warranty |
More information #ad
9. waveshare
#ad
Stepper Motor HAT for Raspberry Pi,Jetson Nano Onboard Dual DRV8825 Motor Controller Built-in Microstepping Indexer Drives Two Stepper Motors Up to 1/32 Microstepping 5V 2.5A
#adwaveshare #ad - Onboard dual drv8825 motor controller ic with built-in microstepping indexer, drives two stepper motors, easy to use; Onboard multi connector options for stepper motors in different specifications.Protection features: overcurrent protection ocp, Thermal Shutdown TSD, vM Undervoltage Lockout UVLO; Integrates 5V regulator, allows providing power to Raspberry Pi.
More information #ad
Standard raspberry pi 40pin gpio extension header, supports Raspberry Pi series boards, Jetson Nano. 6 available microstepping modes, and 1/32-step; adjustable motor drive current via potentiometer, 1/4-step, half-step, 1/16-step, configured with the dip switches: full-step, 1/8-step, maximum 2.5a current output.Brand | waveshare #ad |
Manufacturer | Waveshare #ad |
Part Number | 8541612876 |
Model | 8541612876 |
More information #ad
10. Adafruit
#ad
Adafruit PID 3297 DRV8833 DC/Stepper Motor Driver Breakout Board
#adAdafruit #ad - Spin two dc motors or step one bi-polar or uni-polar stepper with up to 1. 2a per channel. Drv8833 an handle a peak of 2A, but only for a short amount of time. 2. 7v to 108v motor power. Drv8833 motor driver chip. 2 full H-bridges.More information #ad
Brand | Adafruit #ad |
Manufacturer | Adafruit #ad |
Height | 1 Inches |
Length | 3 Inches |
Weight | 0.03 Pounds |
Width | 2 Inches |
Part Number | 3297 |
Model | 8541612111 |
More information #ad