Top 9 L298N Motor Drive Controller – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. MELIFE

 #ad

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
MELIFE #ad - No assembly required. Double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient.

External size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Great for arduino diy smart car robot power uno mega r3 mega2560 duemilanove. Just wire up motors and power, easy to use. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits. Main driver chip l298n, low calorific value, afterflow diode protection, strong driving ability, strong anti-interference, more stable and reliable for Arduino projects. This l298n board comes ready to go.
BrandMELIFE #ad
ManufacturerMELIFE #ad
Part Number15489

2. KeeYees

 #ad

KeeYees L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with DC Motor and Smart Car Wheel Compatible with Arduino

#ad
KeeYees #ad - Motor drive controller: l298n used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability. This is a good parts kit for an arduino and raspberry pi based RC car project.

To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage. Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber. Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability. It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.
BrandKeeYees #ad
ManufacturerKeeYees #ad

3. DAOKI

 #ad

DAOKI 2 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 with Dupont Cable

#ad
DAOKI #ad - Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. The connecting method is shown inbelow figure after enable ENA ENB. The signal is shown in the figure. Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. Package content: 2 x l298n motor drive controller board, 1 x 11. 8" male-male dupont cables 12 PIN, 1 x 11. 8" male-female dupont cables 12 PIN, 1 x 19. 6" 28awg wire.
BrandDAOKI #ad
ManufacturerDAOKI #ad
Part NumberDR-US-254
ModelDR-US-254

4. Generic

 #ad

2Pack L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Compatible with Ar-duino Electric Projects, Smart Car Robot

#ad
Generic #ad - Dual-channel h-bridge driver working mode creates higher working efficiency, Can drive one 2-phase stepper motor, L298N as main chip, one 4-phase stepper motor or two DC motors.

Large capacity filter capacitance, afterflow protection diode, more stable and reliable. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w.
BrandGeneric #ad
ManufacturerDoes Not Apply #ad
Part NumberNA
ModelNA

5. Ltvystore

 #ad

Ltvystore, L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Module Compatible Arduino & Male to Male/Male to Female/Female to Female Breadboard Jumper Wires Ribbon Cables Kit

#ad
Ltvystore #ad - Max power 25w storage temperature: -25 ~ +130 Breadboard jumper wires assorted kit120pcs multicolored dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit Compatible for arduino.

Dual h-bridge motor driver:logical voltage 5v. Drive voltage 5v-35v Drive current 2AMAX single bridge. High quality l298n motor drive controller board : st l298n main driving chip, l298n as main chip. Can drive one 2-phase stepper motor, low calorific value, high drive ability, strong anti-interference capability; Dual-channel H-bridge driver working mode creates higher working efficiency, one 4-phase stepper motor or two DC motors.

Dc stepper motor:use large-capacity filter capacitors and diode with freewheeling protection function, afterflow protection diode, increasing reliability; Large capacity filter capacitance, more stable and reliable. L298n h-bridge motor controller:to avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
BrandLtvystore #ad
ManufacturerLtvystore #ad
Height0.39 Inches
Length0.39 Inches
Width0.39 Inches
Part Numberfive-1006

6. ACEIRMC

 #ad

Organizer 5pcs L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Controller Board

#ad
ACEIRMC #ad - 3. Great for for arduino diy smart car robot power uno mega r3 mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits. 2.

The chip manual proposes to support 35v, for example, but according to the book When the maximum voltage is applied to the maximum voltage of 298 conservative applications to 24V, the motor with a rated voltage of 18V shall be driven.44. No assembly required. 5. This l298n board comes ready to go. Double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient.

Just wire up motors and power, easy to use. 1. When you are driving voltage above logo for the 12 v input, can make to onboard power supply 5 v logic, can actually accept input range is 7 to 12 v for 7 v to 12 v, interface of + 5 v The power supply does not input voltage, when using the onboard after 5 v power supply, but can yield 5V voltage for external use.
BrandACEIRMC #ad
ManufacturerOrganizer #ad
Part Number10544

7. DEVMO

 #ad

Smart Car Robot, DEVMO 10 Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Compatible with Ar-duino Electric Projects

#ad
DEVMO #ad - High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w. Dual-channel h-bridge driver working mode creates higher working efficiency, L298N as main chip, Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.

To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage. Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. Large capacity filter capacitance, afterflow protection diode, more stable and reliable.
BrandDEVMO #ad
ManufacturerDEVMO #ad
Part NumberL298N

8. Generic

 #ad

5Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Compatible with Ar-duino Electric Projects, Smart Car Robot

#ad
Generic #ad - Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability. High working power to 46v, large current can reach 3A MAX and continue current is 2A, power to 25w.

Dual-channel h-bridge driver working mode creates higher working efficiency, Can drive one 2-phase stepper motor, L298N as main chip, one 4-phase stepper motor or two DC motors. Large capacity filter capacitance, afterflow protection diode, more stable and reliable. To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
BrandGeneric #ad
ManufacturerDoes Not Apply #ad
Part NumberNA
ModelNA

9. PChero

 #ad

PChero 2Packs L298N Motor Drive Controller Board Module, Dual H Bridge DC Stepper For Arduino Smart Car Robot

#ad
PChero #ad - Drive voltage 5v-35v, high working power to 46v. Large current can reach 3A MAX and continue current is 2A. Power to 25w. Note: to avoid damage, please use an external 5V logic supply when using more than 12V driving voltage.

High efficiency - dual-channel h-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors. Just wire up motors and power, this thing will work wonders. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module.

Easy of use - no assembly required. High quality - use l298n as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value. Item size - external size 43*43*27mm / 1. 69*1. 69*1. 06 inch. Package included - 2pcs L298N Motor Driver Controller Board Modules. This l298n board comes ready to go.
BrandPChero #ad
ManufacturerPChero #ad
Part NumberiS017