As an Amazon Associate I earn from qualifying purchases.
1. Adafruit #ad
Adafruit Motor/Stepper/Servo Shield for Arduino v2.3 Kit #adAdafruit #ad
- Instead of a l293d darlington driver, we now have the tb6612 mosfet driver: with 1. 2a per channel and 3A peak current capability. You'll still need to do a little soldering to put on the shield-headers or stacking headers but it should be even easier and faster to get started! This chip handles all the motor and speed controls over I2C.
Only two pins sda & scl are required to drive the multiple motors, Leonardo and Mega R3. Instead of using a latch and the arduino's pwm pins, due, such as the uno, and since it's i2c you can also connect any other I2C devices or shields to the same pins.
As of 3/21/2014 we are shipping motor shields with the terminal blocks, and power jumper pre-soldered on. This also makes it drop-in compatible with any Arduino, we have a fully-dedicated PWM driver chip onboard.
It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well. New version 2. 3! completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but if you come up with something send us a photo because that would be a pretty glorious project.
2. MakerDoIt #ad
Makerdoit 4pcs Micro Servo Motor SG90, for Robot Arm/Hand/Walking/Servo Door Lock #adMakerDoIt #ad
- Small sizeit is tiny and lightweight with high output power. Specificationsno load running speed: 012 second/60 at 4. 8v. Package includethe package included 4pcs servo motor SG90, each SG90 come with one motor/ three servo arms and three screws.
Dead bandwidth: 7usec. This servo can rotate approximately 180 degrees 90 in each direction and works just like the standard kinds but smaller. Stall Torque 4.
8v: 17. 5oz /in 1kg/cm. Rotary angle: 180°. Hardware connectionsthe sg90 has 3 wire interfaces in which the connections should be made as follows: Red wire-5V, Brown Wire-Ground, Yellow wire-digital pin 9. Operating voltage: 4. 8v~6v. Program for sg90you can build the project like “Robot Arm/ Robot hand/ control the servo with potentiometer/ multi servo control” and so on.
3. SunFounder #ad
SunFounder SG90 Micro Digital Servo Motor SF0180 for RC Helicopter Airplane Boat Robot Controls 9G 2pack #adSunFounder #ad
- Pack of two micro servos, each SG90 come with one motor/ three servo arms and three screws. Exquisite small, make u realize bulid the robot project, it can suitable for a variety of RC Toys. Dead band width is 5usec. Temperature range is -55 to +75. Operating voltage Range is 4. 8v~6. 0v.
4. Longruner #ad
Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire #adLongruner #ad
- Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board. A, b, c, d four-phase led indicates the status of the stepper motor work. Cable length: about 20cm /8-inch. Stepper motor with a standard interface.
Motor diameter: 1. 1 inches. Wire length：9. 05 inchs. 5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. Good after-sales service. Stepping angle: 5. 625 x 1/64. Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs.
|Warranty||1 year warranty|
5. KEYESTUDIO #ad
KEYESTUDIO 16-Channel 12-bit Servo Motor Driver Board I2C Interface for Arduino R3 Controller #adKEYESTUDIO #ad
- Contains pcb double sided holes, can direct to solder with components to build up prototyping circuits. How to use: search for "keyestudio wiki KS0258" in Google Chrome to get the wiki online tutorial for this product.
This expansion board can directly stack on the controller R3 board and can drive up to 16 servos. Uses i2c input, just occupy A4 and A5 interface on the control board. Servo power supply independent V + input up to 6V.
6. SMAKN #ad
SMAKN Mini USB 24 Channel Servo Motor Driver Controller Module for Arduino #adSMAKN #ad
- Power of servo and control board are separate. Servo power supply: generally DC 5V base on the servo you use. 32-bit cPU. Chip power supply: 6. 5v ~ 12v or 4. 5v ~ 5. 5v one is for USB. Channel: 24 servo speed adjustable.
7. HiLetgo #ad
HiLetgo 5pcs ULN2003 28BYJ-48 4-Phase Stepper Motor with 5V Drive Board for Arduino PI PIC Raspberry Pi #adHiLetgo #ad
- Diameter: 28mm. Hiletgo stepper Motor+ Driver Board. Voltage: 5V. Stepping angle: 5. 625 x 1/64. Speed down stepping motor.
8. ELEGOO #ad
ELEGOO UNO Project Super Starter Kit with Tutorial and UNO R3 Compatible with Arduino IDE #adELEGOO #ad
- The most economical kit based on Arduino platform to starting programming for those beginners who are interested. 100% compatible with arduino uno r3, MEGA 2560 R3, NANO. High quality kit with uno r3.
This is the upgraded starter kits with power supply module, 9V battery with dc. Lcd1602 module with pin header not need to be soldered by yourself. Free pdf tutorialmore than 22 lessons and clear listing in a nice package.
9. KINCREA #ad
Servo, Stepper Motor, LCD1602, KINREA Project Super Starter Kit with Tutorial, Controller Board, Relay etc. with Arduino IDE Projects K4 #adKINCREA #ad
- High quality feedback from our customers makes it more reliable. The most economical kit based with Arduino IDE platform to starting programming for those beginners who are interested. Free pdf tutorialmore than 22 lessons and clear listing in a nice package.
Lcd1602 module with pin header not need to be soldered by yourself. Update version: the kit has 44pcs components with tutorial in a CD including project introduction and source code, add More modules:LED Thermistor Touch sensor module than old version. 100% compatible with mega 2560 R3, NANO.